What a PoE switch power budget measures
A PoE switch is the power sourcing equipment (PSE). The camera or access point is the powered device (PD). The maximum power a port can supply at the switch and the maximum available at the device are different figures because the cable channel uses some of that power. For example, IEEE Type 2 supports up to 30 W at the PSE port and up to 25.5 W at the device. Compare switch-side numbers when you add up the PoE switch power budget.
| IEEE designation | PoE type | Maximum at the switch port | Maximum available at the device |
|---|---|---|---|
| 802.3af | Type 1 | 15.4 W | 12.95 W |
| 802.3at | Type 2 | 30 W | 25.5 W |
| 802.3bt | Type 3 | 60 W | 51 W |
| 802.3bt | Type 4 | 90 W | 71.3 W |
These figures are the upper limits for each type. Actual power allocation depends on the device class, the switch model and its configured allocation method. Confirm the supported port types on the exact switch model, including any differences between port groups. For the total PoE switch power budget, use the manufacturer’s specification for the power supplies and operating mode you plan to deploy. For an example of how standards map to switch capabilities, see Cisco’s PoE configuration guide.
Which wattage should go into the calculation?
Start with the device datasheet, the features you intend to run and the switch vendor’s allocation rules. Depending on the platform, a switch may allocate power by class or refine the allocation through Link Layer Discovery Protocol (LLDP) when both ends support it. Put the expected switch-side allocation in your worksheet. A camera’s measured draw at midday is useful for monitoring. The allocation figure is the one to compare against the PoE switch power budget when the switch reserves power by class.
- IP cameras. Check the maximum demand for the selected configuration, especially outdoor models with heaters or infrared illumination. Some models publish separate figures for different features or accessories. Review those conditions when you scope IP security camera installation.
- Wi-Fi access points. Check the vendor’s power requirements for the radio, port and accessory features you need. Some access points start up at a lower PoE level with reduced features. Confirm the intended operating mode when planning building-wide Wi-Fi coverage.
- Switches and power supplies. Use the published PoE capacity for the actual supply configuration. Record the budget available in the required backup mode if the site needs continued service after losing a supply or power feed.
Worked PoE switch power budget example
Consider a Toronto office with eight indoor cameras, four outdoor cameras and two Wi-Fi access points on one 24-port switch. Assume the selected switch offers 370 W of usable PoE power in its planned operating mode. The numbers below are illustrative switch-side allocations. Substitute the values supported by your actual equipment.
| Device | Quantity | Allocation per port | Total allocation |
|---|---|---|---|
| Indoor IP camera | 8 | 15.4 W | 123.2 W |
| Outdoor IP camera | 4 | 30 W | 120 W |
| Wi-Fi access point | 2 | 30 W | 60 W |
| Total | 14 | — | 303.2 W |
The remaining PoE switch power budget is 370 W − 303.2 W = 66.8 W. Adding two more access points at 30 W each would leave 6.8 W. If the building owner requires 40 W to remain available after the expansion, the project needs at least 403.2 W of usable capacity or a different distribution of devices across switches. Check the assigned ports individually as well. A planned 60 W access point needs a suitable port even when 66.8 W remains available across the switch.
Use a separate calculation for each switch or wiring closet. A building-wide total can hide a shortage on the switch that serves the car park or the busiest floor. Compare each closet’s device list with its available ports, power and structured cabling and fibre routes before finalizing the layout.
How to calculate a PoE switch power budget step by step
Work through these six steps for each switch. Keep the worksheet with the device list so the next person adding a camera or access point can see how much capacity is available.
-
Make a device inventory by switch
List every camera, access point and other PoE endpoint. Record the model, quantity, wiring closet, planned switch port and features that must be enabled.
-
Identify the power each device needs
Find the PoE type, class and power requirements for the planned configuration. Confirm the switch-side allocation using the switch vendor’s documentation. Use one consistent set of switch-side values throughout the calculation.
-
Check the assigned ports
Match each device to a port that supports its PoE type and allocation. Verify any high-power ports separately and check that the cabling channel meets the equipment requirements.
-
Add the switch-side watts
Multiply each per-port allocation by the number of matching devices. Add those subtotals to get the total allocated load for the switch.
-
Check the budget for normal use and expansion
Subtract the allocated load from the usable PoE switch power budget. Deduct the watts for planned additions and compare what remains with the agreed reserve. Repeat the check with the reduced supply capacity if the site requires failover operation.
-
Verify the installed equipment under expected load
Review the switch’s allocated and available power readings. Test the camera modes, confirm that access points run with the required features and document the final port assignments and remaining watts.
Frequently asked questions
What is a PoE switch power budget?
It is the total power the switch can supply to PoE devices in a specified operating configuration. The power limit of each individual port also applies, so an endpoint must fit within both the port capability and the switch’s remaining budget.
Does a 24-port PoE+ switch provide 30 W on all 24 ports at once?
That depends on its total usable budget. Providing 30 W on all 24 ports at once would require 720 W of PoE capacity and 24 ports rated for that allocation. Check both figures in the switch specifications.
How much spare capacity should I leave in a PoE switch power budget?
Estimate the watts for planned additions, then agree on a reserve based on the site’s expansion and availability needs. If the design has to survive a supply failure, confirm how much reserve remains in that operating mode as well.
Should I add cable loss to the switch’s allocated watts?
If the value is already the switch-side allocation, use it directly in the total. If the datasheet only gives power at the powered device, confirm the corresponding switch-side allocation from the equipment class or manufacturer documentation before adding it.
What happens if the PoE switch power budget is exceeded?
Depending on the switch and configuration, it may deny power to a new device or remove power from lower-priority ports. Check the event log and compare the required allocation with the available budget and the limit of the affected port.
Plan PoE capacity for a Toronto property
Bring your floor plans, device models and switch specifications to the network design discussion. Smartopia can review the PoE switch power budget alongside the cable routes and expansion plans for the property. Start with a network cabling assessment in Toronto.

Comments are closed